Pipe Insulation, 54mm, 2mx1m, 20mm Insulation, Foam Pipe Insulation, Insulation Tubing

Yes, the insulation hose meets the requirements of the GEG and DIN 1988 200 and EN 806-2. It is therefore in accordance with the standards for use in heating and sanitary areas.

Yes, the CLIMAFLEX® offers sound-absorbing properties for acoustic comfort. Insulating the pipeline behind the water meter can reduce noise transmission into the apartment.

Yes, CLIMAFLEX® is a CO2-neutral product throughout the entire manufacturing process and consists of NMC Naturefoam® with at least 50% renewable raw materials. It improves the ecological efficiency of the system.

The CLIMAFLEX® insulation hose meets the GEG and DIN requirements (specifically DIN 1988 200 and EN 806-2). It is therefore in conformity with the applicable standards for the heating and sanitary sector.

The insulation hose is flexible and designed for pipes with an outer diameter of 54 mm. It can be easily pushed on if the pipe size is correct, and a second person can be helpful for longer pipes. A pipe with a circumference of about 17 cm fits exactly (roughly calculated: circumference / Pi = diameter).

Please note that for shipping reasons, we cut the 2m bar into 2 x 1m bars. You will therefore receive two bars of 1 m.

The insulation hose with 20 mm insulation thickness has a fire behavior of CLs1d0. This is a very good classification, which means low smoke development and no burning drips in case of fire.

The insulation hose is made of flexible, foamed polyethylene. This makes it easy to lay it around curves and bends.

Yes, in addition to thermal insulation, CLIMAFLEX® also offers a sound-dampening function. This can help reduce flow noise in the pipes and thus improve acoustic comfort.

Yes, the insulation hose is designed for permanent use in the specified temperature range of 0°C to +100°C. The materials are stable under these conditions.

With an insulation thickness of 20 mm, the CLIMAFLEX® insulation hose meets the requirements for professional thermal insulation for heating pipes. It is GEG-compliant and can save up to 80% energy.

Yes, the insulation hose is explicitly suitable for cold water pipes according to DIN 1988 200. It helps to save energy and prevent condensation.

The insulation hose is delivered in two 1-meter pieces and can be easily cut to size if needed. You can easily adapt it with a sharp knife or scissors.

Yes, the CLIMAFLEX® insulation hose is made of foamed polyethylene with at least 50% renewable raw materials. It is also CO2-neutral throughout the entire manufacturing process.

Yes, the 20 mm insulation of the CLIMAFLEX® significantly reduces the heat emission from the hot water pipes. This helps to keep the room temperature stable in summer and reduce energy consumption. The product offers energy savings of up to 80%.

A low thermal conductivity means that the material conducts heat very poorly. For you, this means that less heat is lost through the pipes, which noticeably reduces your heating costs.

Yes, the CLIMAFLEX® insulation hose is designed for use from 0°C to +100°C. It is therefore very suitable for insulating hot water pipes in sanitary areas to save energy.

Yes, the CLIMAFLEX® is suitable for cold water pipes according to DIN 1988 200. The closed-cell structure of the material effectively prevents condensation.

The assembly of the flexible insulation hose is usually straightforward. It is simply pushed over the pipe. If necessary, it can be cut to size, which makes handling easier even for laymen.

The product is made of foamed polyethylene based on NMC Naturefoam®, which consists of at least 50% renewable raw materials. In addition, the entire manufacturing process is CO2-neutral, which contributes to a positive environmental balance.

The insulation hose is supplied in 2x1m pieces. A piece of pipe with a maximum length of 1 meter can thus be insulated "in one piece". For longer sections, the pieces are lined up and the joints are sealed. (Roughly calculated: A 2m delivery thus covers two 1m pipe sections or a 2m section with one joint.)

The insulation hose has an inner diameter of 54 mm. For a pipe with an outer diameter of 50 mm, it would therefore be a bit too wide, but would still insulate in principle. An optimal fit is given for pipes with exactly 54 mm outer diameter.

Yes, the professional thermal insulation with this product can contribute to energy savings of up to 80%. This noticeably improves the economic efficiency of your system.

The temperature range of the insulation hose is between 0°C and +100°C. At temperatures below freezing, it offers an insulating effect, but freezing at a permanent drop below 0°C on uninsulated pipes is not entirely excluded.

Yes, the CLIMAFLEX® is suitable for cold water pipes according to DIN 1988-200. The professional thermal insulation effectively helps to reduce condensation.

Yes, the CLIMAFLEX® meets the GEG and DIN requirements. It is specially designed for the heating and sanitary sector as well as for cold water pipes according to DIN 1988-200.

Yes, the insulation hose has a fire behavior class CLs1d0 for the 20 mm insulation thickness. It also meets the GEG requirements for the heating and sanitary area, which ensures safe use.

Yes, the insulation hose is suitable for steel pipes, regardless of galvanization. The material composition is compatible with steel.

The insulation hose is made of closed-cell polyethylene, a robust material. This is resistant to common stresses in heating and sanitary areas.

The 1-meter pieces should be joined end-to-end and the joints carefully sealed with a suitable insulation tape or special adhesive for pipe insulation. This way, the insulation effect remains optimally maintained.