Self-Adhesive Pipe Bend Insulation - 35mm, 13mm Thick

The 13 mm insulation thickness is designed for effectively reducing heat loss in heating and sanitary areas. They offer good insulation performance while requiring little space.

The insulation is specially designed for pipes with an outer diameter of 35 mm. It adapts optimally to the corresponding pipe elbows.

The insulation is made of flexible polyethylene and adapts well to common pipe bends. The diameter of 35 mm is intended for standard pipes in sanitary and heating systems.

The bow insulation is suitable for heating and sanitary areas up to +100°C. For processing, the temperature should not be below 5°C. Permanent use outdoors or in frost is not recommended.

Yes, the insulation is made of closed-cell polyethylene and is excellent for preventing condensation on cold water pipes. This is a typical area of application.

The flexible polyethylene material is designed to adapt optimally to pipe bends. It allows a certain flexibility during installation, even for slightly deviating angles.

Yes, the insulation is self-adhesive and the flexible polyethylene material adapts well to different surfaces. However, a cleaned, dry and grease-free surface is always recommended for optimal adhesion.

Yes, the self-adhesive layer is designed for permanent installation and also holds for overhead mounting. Careful application on a clean surface is crucial for durability.

The arch is classified according to Euroclass E (EN 13501-1). This means that the material is normally flammable and does not offer special fire protection, as would be required for fire-resistant bulkheads.

The arch is delivered in gray. Overpainting with wall paint is not explicitly stated and may affect the material properties or adhesion.

Yes, the bend is designed for use in heating and sanitary areas. The temperature range is up to +100°C.

The insulation significantly minimizes heat loss due to its low thermal conductivity (e.g. 0.040 W/mK at 40°C). The exact savings depend on many factors. But it lowers energy costs through efficient insulation.

Polyethylene is a widely used material in the sanitary sector and is odorless in the intended temperature range up to +100°C. No significant emissions are to be expected.

The temperature range of the bend is up to +100°C, but processing should not be carried out below 5°C. The product is not primarily designed for outdoor use in frost, as it does not explicitly meet the requirements for drinking water pipes outdoors.

The processing temperature for this insulation should not be below 5°C to ensure optimal adhesive strength and material flexibility. Please ensure an appropriate room temperature in the basement.

The material is closed-cell polyethylene, which has a certain robustness. It protects against light impacts, but is not designed for strong mechanical abrasion or high stress.

Yes, this elbow insulation is universally designed for pipes in the heating and sanitary sector. It can also be used for copper pipes without any problems.

The insulation is self-adhesive for permanent attachment. Reusing it after removal is not recommended due to the adhesive properties.

The closed-cell polyethylene material effectively prevents condensation. The adhesive layer is designed to adhere permanently to dry and clean surfaces.

The processing temperature should not be below 5°C to ensure optimal adhesive properties and material flexibility.

Yes, the insulation arch made of closed-cell polyethylene effectively protects your pipes from frost. It is specially designed for use in heating and sanitary systems.

The installation of the insulation is described as straightforward and efficient. Special tools are not strictly necessary for the pure assembly of the arch piece, but a sharp knife for adjustment and tape for fixing the edges are helpful.

Yes, the insulation is made of closed-cell polyethylene and effectively protects against heat loss and frost. This also helps prevent condensation on cold water pipes in plumbing systems.

The insulation thickness of 13 mm is designed for standard heating and sanitary pipes in indoor areas. It provides effective protection against heat loss and contributes to energy efficiency.

Yes, the insulation arc is designed for use in heating and plumbing. It also provides effective frost protection on cold water pipes.

No, the material of the insulation arc is closed-cell polyethylene. It does not absorb moisture and is resistant to wetness or condensation.

Yes, the insulation is specifically designed for use in heating and sanitary systems. This includes drinking water pipes, where it protects against heat loss or freezing.

The insulation is specifically designed for use in heating and sanitary systems. This area is typically indoors. Information on UV resistance for outdoor use is not listed.

The simple bend shape facilitates installation. However, note that the bend itself has an insulation thickness of 13 mm and therefore requires additional space around the 22 mm pipe. Check the available space before installation.

The installation of the insulation is described as "easy." For a permanent and effective seal against heat loss, a special adhesive or insulation tape is typically used at the joints. The bow itself is pre-formed.