Self-Adhesive Pipe Insulation, 54mm, 2x1m, 9mm - Heating & Plumbing

The self-adhesive closure of the CLIMAFLEX® XT is designed for permanent and quick assembly. Re-detaching and re-attaching is not intended and can significantly impair the adhesive performance. Plan the length exactly before gluing.

Yes, the fire protection class is also relevant for pipes running in the wall for building safety. The CLIMAFLEX XT meets a high fire protection requirement with BLs1d0.

Although the insulation hose has a proven, double-sided self-adhesive closure system, additional fixing with cable ties or special insulation tape is possible, but not mandatory.

Yes, the insulation hose is also suitable for cold water pipes according to DIN 1988 200. It prevents condensation and can be used for temperatures from 0°C to +100°C.

This insulation is made of NMC Naturefoam® with at least 50% renewable raw materials and is CO2 neutral throughout the entire manufacturing process. It has a positive environmental balance.

The temperature range of the insulation hose is between 0°C and +100°C. At 70°C, it still has a thermal conductivity of 0.045 W/mK, which ensures a good insulation effect.

Yes, the foamed, closed-cell polyethylene is very flexible. It adapts well to pipelines with corners and bends and ensures continuous insulation.

The insulation hose is designed for the heating and sanitary sector, which is typically indoors. Although the temperature range is from 0°C to +100°C, no explicit resistance to weather influences such as rain or permanent UV radiation is shown.

The insulation hose is specially designed for pipes with an outer diameter of 22 mm. For 20 mm pipes, this hose would be a bit too large in inner diameter and would not fit optimally.

Yes, the classification BLs1d0 means a very good fire behavior. Compared to many standard insulations, CLIMAFLEX XT is characterized by low smoke development and no burning dripping, which significantly increases safety.

The insulation hose is designed for a temperature range of 0°C to +100°C. Therefore, it is very suitable for your 90°C hot water pipes.

For optimal and permanent adhesion of the self-adhesive closure, the pipes should be clean, dry and free of grease before installation. Light dust can affect the adhesive strength.

Thanks to the self-adhesive closure system, assembly is up to 50% faster. For 10 meters of pipe insulation, you should, depending on experience and accessibility, allow about 15-20 minutes. (Roughly calculated: 1-2 minutes per meter of insulation hose).

Yes, the insulation hose is also suitable for cold water pipes according to DIN 1988 200, in addition to the heating area. So it can be used for various sanitary pipes.

Yes, the CLIMAFLEX® XT is suitable for cold water pipes according to DIN 1988 200 in addition to the heating and sanitary sector.

Yes, the material has sound-absorbing properties and can also help reduce noise and vibrations, for example from heating pumps, by decoupling the pipes.

The insulation hose is designed for pipes with an outer diameter of 22 mm. DN20 can have a different outer diameter depending on the material (copper, steel). Please measure the exact outer diameter of your pipe.

Yes, the insulation reduces heat losses on heating pipes by up to 80%. This leads to a significant and measurable energy saving and thus to reduced heating costs.

Yes, the CLIMAFLEX® XT can be used for cold water pipes according to DIN 1988 200. This usually also includes drinking water pipes.

No, thanks to the double-sided self-adhesive closure system, no special equipment is required for assembly. A sharp knife for cutting is sufficient.

Yes, the CLIMAFLEX® XT is GEG compliant and meets the necessary DIN requirements. Thus, it is ideally suited for the energy-efficient renovation of old buildings.

The product description of the CLIMAFLEX® XT does not mention specific UV resistance. The material is primarily designed for heating and sanitary areas indoors. Direct, permanent sunlight should be avoided so as not to affect the longevity.

CLIMAFLEX XT is made of foamed, closed-cell polyethylene with a high proportion of renewable raw materials. It is a low-odor and low-emission product that is safe for indoor use.

Yes, the CLIMAFLEX® XT has sound-dampening properties. It reduces cracking and flow noises in the pipes, thus ensuring more acoustic comfort.

Yes, the self-adhesive closure system of the CLIMAFLEX® XT enables a quick and clean attachment even to already laid pipes, saving up to 50% of the assembly time.

The material is easy to cut. Thanks to the double-sided self-adhesive cutting edge, insulating laid cables is twice as fast as with conventional products.

The fire behavior of the CLIMAFLEX® XT is classified as very good with BLs1d0 according to EN 13501-1, which ensures high safety.

Yes, the insulation has sound-dampening properties. It reduces cracking and flow noises in the pipes and thus contributes to better acoustic comfort.

The double-sided self-adhesive cut edge of the CLIMAFLEX® XT is optimized for quick and clean processing. For optimal and permanent adhesion, the surface should be dry and clean. With high permanent humidity, the adhesive performance can suffer.

Yes, CLIMAFLEX XT is made of closed-cell polyethylene and is specially suitable for cold water pipes according to DIN 1988 200. It effectively prevents condensation and the associated problems.