Malleable Iron 45 Degree Elbow, 2 Inch Threaded Fitting

Yes, the standardized Whitworth pipe threads of the angle allow for a seamless transition to pipes made of other materials such as PVC, provided they have a matching thread.

The elbow is made of V4A stainless steel, which is generally suitable for drinking water applications. Specific certifications for Germany, however, are not explicitly listed.

The angle is designed for industrial plant construction. Suitability for specific chemical liquids depends on their nature and should be checked on a case-by-case basis.

The angle requires additional thread sealing material. Hemp or Teflon tape is very suitable for this.

Yes, the flow direction is irrelevant for this angle, it can be mounted on both sides. Installation is done with standard tools for threaded connections.

Yes, the corner piece is suitable for both cold and hot water. It withstands temperatures from -20 °C to +200 °C.

Yes, the stainless steel fittings are designed to be permanently released and reused. Ensure a clean disassembly and use new sealing material upon reuse.

To seal the thread, you need suitable thread sealing material. Hemp or PTFE thread sealing tape is suitable, both are common in water technology.

Yes, the corner piece is made of stainless steel 316 (V4A), which is rust-free and permanently corrosion-resistant. It is also suitable for use with saltwater.

The threads of the angle piece allow for a seamless transition to other materials. A connection with plastic pipes via appropriate adapters is thus possible.

The bracket is designed for temperatures from -20 °C to +200 °C and is thus suitable for applications like solar thermal on the roof. The material stainless steel 316 ensures longevity under these conditions.

Yes, the angle is designed for working pressures up to 10 bar. A pump with 7 bar is within this safe pressure range and will withstand it permanently.

No, the corner piece is designed for a maximum working pressure (PN) of 10 bar. 15 bar is above the specified range.

The elbow is made of stainless steel 316 (V4A), a material that is common and safe for drinking water installations. It is suitable for both cold and hot water.

Yes, the angle is specifically designed for a 45-degree change in direction in the piping system. It provides a firm and defined incline.

The corner piece is made of stainless steel 316 (V4A steel) and is therefore permanently rust-free and corrosion-resistant. It is suitable for use in demanding environmental conditions such as acid rain.

The corner piece is designed for pressure ranges up to 10 bar. This is usually sufficient for common garden fountain systems.

The angle is designed for a temperature range of -20 °C to +200 °C. Therefore, it can also be used outdoors in frost.

The angle is suitable for temperatures from -20 °C to +200 °C and can therefore also be used in hot water systems such as heating circuits.

Yes, the fitting is designed for pressure ranges up to 10 bar. It can therefore also be used for compressed air lines up to 8 bar.

The angle is suitable for both cold and hot water. The temperature range is from -20 °C to +200 °C.

The external dimensions of the angle are approximately 20 mm (A) x 30 mm (B). Plan some extra space for installation and tightening the threads.

The angle is made of stainless steel 316 (V4A), which has high resistance to many chemicals. However, suitability for specific aggressive media depends on concentration and temperature.

Yes, the stainless steel angle is rust-free, corrosion-resistant, and approved for temperatures down to -20 °C. Permanent outdoor use is therefore possible without any issues.

Yes, the angle is made of stainless steel 316 (V4A), which is rust-free and corrosion-resistant and suitable for salty environments.

Yes, the angle is designed for a working pressure of up to 10 bar. An irrigation system with 6 bar is therefore not a problem for the fitting, and it will withstand the pressure in the long term.

Yes, the angle is made of stainless steel 316 (V4A) and is therefore rust-free and corrosion-resistant. It can be permanently installed in damp environments like basements or garden houses without any issues.

No, the 1/4 inch thread is a Whitworth pipe thread and is not compatible with NPT connections. Despite the tapered external thread, additional sealing with hemp or Teflon tape is mandatory for permanent tightness.

Yes, the angle is designed for temperatures from -20 °C to +200 °C. It can therefore be used without any problems in solar thermal systems, even if the water exceeds 100 degrees.

The angle is designed for a working pressure of up to 10 bar. This is sufficient for most pressure booster pumps.