Brass Y Hose Connector with Shut Off Valves

Yes, the shut-off valves on the outlets allow you to individually regulate the water flow. This way you can control the amount of water in a targeted manner.

The Y-splitter is designed for splitting one water source into two outlets. Combining two sources into one hose is not intended with this device.

No, the quick coupling of the Y-splitter is made of pressed brass with a standardized 40 mm lug spacing. Only matching couplings can be connected.

Yes, the Y distributor made of pressed brass is resistant and can usually also be used for water with liquid fertilizer additives. However, it should be rinsed well with clear water after use.

The integrated quick couplings allow you to easily and quickly connect hoses and accessories. They are suitable for common systems.

The Y-splitter has quick couplings made of pressed brass with a 40 mm lug spacing. These are suitable for common systems like GEKA.

The Y-splitter is made of robust pressed brass, which is known for its durability and corrosion resistance.

The Y distributor is equipped with Geka-compatible quick couplings (40 mm lug spacing). For connecting Gardena hoses, you will need the appropriate adapters from Gardena to Geka.

Yes, the Y-distributor is ideal for operating two separate irrigation circuits in parallel. The individual shut-off valves allow flexible control of each circuit.

Yes, the Y-splitter is equipped with 3x GEKA-compatible quick couplings and fits common systems like GEKA.

The robust construction made of pressed brass guarantees durability and reliability. Brass is corrosion-resistant and does not rust like iron.

Regular cleaning with clear water and occasional greasing of the moving parts with suitable valve grease can maintain the smooth operation of the ball valves and couplings.

The ball valves are designed for easy operation and can usually be operated without much effort. The quick couplings also allow for easy connection of the hoses.

Due to the design, the flow rate is reduced when using the distributor. For two consumers such as drip irrigation and sprinkler, this can lead to a reduction in performance at both outlets.

The quick couplings of the Y-distributor are designed for a reliable and tight connection. When installed correctly, they withstand the usual water pressure in the garden.

Yes, the Y-distributor is equipped with shut-off valves. The outlets can be shut off individually with ball valves.

It is recommended to reduce the water pressure before disconnecting the hoses to facilitate handling and protect the seals. Geka-compatible couplings may be more difficult to disconnect under pressure.

The robust construction made of pressed brass is designed for durability and reliability. The material is known for its resistance in outdoor use.

The Y-distributor allows simultaneous operation of several devices. Due to the design, the flow is reduced, which can lead to a noticeably lower pressure with two sprinklers running simultaneously.

The Y-splitter fits common systems like GEKA etc. It has a quick coupling made of pressed brass with a lug spacing of 40 mm.

The Y-distributor is primarily designed for garden irrigation with tap water. Use with service water is possible under certain circumstances, but may affect the lifespan and tightness.

The Y distributor is equipped with Geka-compatible quick couplings with a lug spacing of 40 mm. To connect to a normal water tap, you need a suitable Geka tap connector.

The brass material is robust, however, we recommend disassembling the Y-distributor BONI-53306 in winter and storing it in a frost-free place. This protects the ball valves from frost damage.

The brass Y-splitter is designed for use with normal cold water in the garden. Continuous use at temperatures above 40-50°C is not recommended and can damage seals and material.

The splitter is made of robust pressed brass, which makes it very resistant. An accidental fall from a low height should not normally cause any damage.

Yes, the outlets of the Y-splitter can be shut off individually by integrated ball valves. This allows you to control the water flow individually.

Please note that the flow is reduced due to the design when the distributor is used. This can affect the performance of connected devices.

The Y distributor has no integrated mounting points for wall mounting. Fixing it to the wall would only be possible via separate clamps or a mounting plate.