1 Inch Brass Tee Fitting (3x Female 1" IG & 3x Male 1" AG Threaded) - High-Quality Brass Component

Yes, the BONI-53320 is made of hot-pressed brass and meets the requirements of the drinking water ordinance. It is therefore safe for use in drinking water installations.

Yes, the T-piece has a standardized DIN EN ISO 228-1 thread and can be connected with the appropriate adapter pieces or directly to compatible steel pipes. It is important to use suitable sealants.

Yes, the scope of delivery of the T-piece BONI-53320 includes three brass threaded pieces with 1" male thread (AG). These enable flexible use of the 1" female thread (IG) connections.

For the threads of the T-fitting, we recommend using PTFE tape or hemp with sealing paste. Pay attention to a clean and tight screw connection for optimal tightness.

Yes, the BONI-53320 T-piece comes with three separate brass threaded pieces 1" AG. You can therefore provide all three 1" female threaded connections of the T-piece with an external thread.

Yes, the T-piece is designed for heating installations and is made of hot-pressed brass. It can withstand the temperatures and pressures typically found in solar water heating systems.

Yes, the T-piece is also suitable for various applications in garden irrigation due to the robust brass material and standard threads.

With professional installation and the use of suitable sealants, the T-piece is permanently sealed and does not require regular checks or retightening of the connections. It is designed for long-term use.

The T-piece is designed for easy handling and can be mounted with standard installation tools. A firm, but not over-tightened screw connection is crucial for the seal.

Yes, the brass T-fitting is designed as a reliable and durable solution for heating installations. It is made of hot-pressed brass.

The T-piece is made of hot-pressed brass, which is very corrosion-resistant and complies with the drinking water regulations. Brass is well-suited for permanent underground installation, but additional protection can further increase its lifespan.

Yes, the T-piece is suitable for sanitary installations such as laying water pipes and creating branches.

The brass T-piece is corrosion-resistant and can generally also be installed outdoors under the influence of the weather. The longevity of brass is an advantage here.

Yes, the T-piece is explicitly designed for sanitary and heating installations. It withstands the usual temperatures and pressures in heating systems.

The three brass threaded pieces 1" external thread (AG) are supplied separately and are not pre-assembled. They can be easily screwed into the internal threads of the T-piece if required.

For the threaded connections of the T-piece, you can use standard sealants such as Teflon tape, hemp or suitable sealing rings. Special seals are not required.

The 1-inch connections correspond to a standardized thread according to DIN EN ISO 228-1. The nominal inner diameter is approx. 25.4 mm (which corresponds to about 1 inch).

No, this brass T-fitting is explicitly intended for sanitary and heating installations as well as drinking water pipes. Special, approved fittings are required for gas installations.

The connections of the T-piece have a standardized 1-inch thread (DIN EN ISO 228-1). This is a common standard that is compatible with most standard garden pumps.

Yes, the T-piece is suitable without restriction for use with cold water in sanitary installations and garden irrigation systems.

The brass T-piece is corrosion-resistant and suitable for outdoor applications. For permanent underground installation, additional protective measures against mechanical stress should be considered.

Yes, the brass T-piece is designed for sanitary and heating installations as well as garden irrigation. It is therefore well suited for branching off water pipes for a garden tap.

Yes, the brass T-piece is ideally suited for use in rainwater harvesting systems in the basement due to its material and high quality.

Yes, the T-piece is made of hot-pressed brass, a very corrosion-resistant material. It is designed for permanent use in sanitary and heating installations and is therefore also suitable for damp environments.

Yes, the brass T-fitting has three 1-inch connections and is great for splitting a water line into two separate lines, for example, for two sinks.

Yes, the T-piece is intended for use in heating installations and is therefore also suitable for applications with hot water.

The T-fitting is made of hot-pressed brass and meets high quality standards for sanitary installations. It is robust enough for the usual pressures in domestic water supplies, even with pressure booster pumps.

The T-piece is made of hot-pressed brass and is designed for sanitary and heating installations. It offers a reliable solution even for main water pipes in the house.