Graphite Downspout Connector - System 90 Rain Gutter Coupling

Yes, for a precise fit, you should cut the downpipe at a right angle with a fine-tooth saw. This ensures a clean and secure connection with the sleeve.

For large warehouses, the 90mm connector is suitable in combination with the BRYZA systems 100 or 125. These systems are intended for small to large storage and industrial buildings.

Yes, the type of connection of the downpipes with the sleeves is designed so that thermal changes in length of the gutter system parts can be compensated for.

The BRYZA gutter system has been an established product on the market since 2004. The materials are designed to withstand the stresses of weather and temperature fluctuations, which implies good UV stability.

No, the 75 gutter system uses downpipes with a diameter of 63mm. This connector is exclusively for 90mm downpipes of the 90 system.

The downpipes are simply pushed into the connecting sleeve. No special tools are required for the assembly of the sleeve itself, only a fine-toothed saw for cutting the pipes.

The connector is designed to function reliably even without an additional seal and compensates for thermal length changes of the downpipes. Correct installation at right angles ensures functionality.

Yes, the 90mm downpipe connector is very suitable for single-family homes. It is used in the BRYZA systems 100 and 125, which are explicitly designed for this type of building.

Yes, the graphite color of the downpipe connector corresponds to RAL 7021. This ensures a harmonious look with other system parts in graphite.

Yes, the type of connection of the downpipes is designed so that thermal changes in length can be compensated for. This ensures tightness during temperature fluctuations.

Yes, the connector for 90mm downpipes is suitable for gutter systems (100mm or 125mm) that are also used on small and medium-sized industrial or warehouse buildings.

The connector is a specific element of the BRYZA plastic gutter system. A reliable connection and tightness with downspouts made of other materials or systems cannot be guaranteed.

This downpipe connector is explicitly part of the BRYZA GUTTER SYSTEM and is designed for its 90mm downpipes. Compatibility with downpipes from other manufacturers cannot be guaranteed.

This connector is specially designed for downpipes with a diameter of 90 mm within the BRYZA gutter system. It is intended as part of the 90, 100 and 125 systems, which use 90mm downpipes.

Yes, the downpipe connection via the sleeve is deliberately designed without a separate seal and still ensures the required tightness of the system with correct assembly.

Yes, the sleeve is used to connect downpipes of the BRYZA System 90. This allows the rainwater to be diverted into a rainwater barrel. Note other required system parts such as bends or T-pieces.

The downpipe connection is designed to compensate for thermal length changes of the system parts. This ensures a permanently secure hold and tightness without additional sealants.

Yes, the gutter system with 90mm downpipes (as part of the 100 or 125 system) is suitable for single-family and multi-family houses. This connector is suitable for such downpipes.

The downpipes are connected to the pipe fittings with the connecting sleeves without a seal. As a rule, no special tools are required for this, the parts are plugged into each other.

Yes, the downpipe connection is made by simply plugging the downpipes into the sleeve. No special tools or seals are required for this.

Yes, the faucet is equipped with a rubber profile seal that ensures reliable tightness.

Yes, the sleeve can be cut with a fine-tooth saw at a right angle to the required length.

The post is ideal for small residential buildings, canopies, garages, balconies, and attics.

The connection is sealed with a rubber gasket that ensures a secure tightness.

The support is designed for smaller buildings. For public buildings, the 100 or 125 system is recommended.

No, the post is designed for smaller buildings. For industrial buildings, the 100 or 125 system is recommended.

The socket is available in brown (RAL 8017).

Yes, the support is suitable for garages, carports, and similar small buildings.

Yes, the support is suitable for attics and similar smaller buildings.

The distance between the holders should be 40 to 50 cm to ensure secure mounting.