Aqua Dicht - transparent sealing compound, fiber-reinforced, 1 L can

The fiber reinforcement helps to bridge cracks and smaller leaks up to a few millimeters. For holes of about 1 cm in diameter, the sealant alone is not sufficient for a permanently reliable seal; here, preliminary work with filler material or other repair methods might be more advisable.

Yes, the product can basically be used to seal leaky folds on sheet metal roofs, as it adheres to metal. For optimal and permanent adhesion, however, strong, loose rust should be removed or treated beforehand.

For optimal adhesion and curing, the surface must be dry, clean, and free of grease before applying Aqua Dicht. Application on damp surfaces is not recommended.

Aqua Dicht is highly flexible and crack-bridging up to 10 mm, which makes it suitable for smaller moving joints. However, it is not a substitute for special expansion joint profiles.

Aqua Dicht is a fiber-reinforced sealant that generally adheres well to GRP and many plastics. For plastic hoses, the compatibility depends heavily on the specific plastic. We recommend performing an adhesion test in an inconspicuous area before full application.

The compound is not suitable for surfaces that are permanently underwater. However, it can be used for pond edges that are only occasionally wet, but only if the ground is dry.

Aqua Dicht is easy to apply. For smaller repairs, you can use a spatula, a brush, or a cartridge gun, depending on the size of the crack or joint.

Yes, Aqua Dicht is brushable and can be easily applied with a spatula, brush or roller on larger surfaces. The consistency allows for easy and even processing.

Yes, Aqua Dicht is a transparent sealant. The transparency is maintained even with multiple layers, as long as the layer thickness does not become excessive.

No, Aqua Dicht should be applied at an ambient temperature of at least +5°C to ensure optimal curing and adhesion. It only achieves full resistance to temperatures from -25°C to +80°C after complete curing.

Yes, Aqua Dicht is specially designed to seal even directly under water. It seals immediately and adheres reliably.

The consumption is about 1-2 liters per square meter. A 1-liter can of Aqua Dicht is therefore sufficient for about 0.5 - 1 m². (Roughly calculated: For 0.5 m² you need about 0.5 to 1 liter).

Aqua Dicht also adheres to glass, provided the surface is clean, dry and free of grease. However, it is not an adhesive, but is used to seal cracks and joints.

For a garage wall, we generally recommend one to two coats, depending on the condition of the cracks and the substrate. With one liter of WF-157404, you can seal about 1.5 to 2 square meters per coat. For 15 m² of wall surface, you therefore need roughly 15 to 20 liters of the product for two coats.

If the product becomes too thick, you can thin it with acetone to restore its spreadability. The sealing effect remains fully preserved after the acetone evaporates.

A quick seal is achieved after a short time. Full curing takes about 24-48 hours, depending on layer thickness and temperature.

Aqua Dicht has high elasticity and is absolutely weatherproof. It reliably bridges cracks and permanently withstands movements caused by temperature fluctuations.

Yes, the sealant is suitable for roof surfaces and bridges cracks up to 10 mm. The surface should be clean, dry, and free of grease before application.

Yes, Aqua Dicht adheres well to pre-treated wooden surfaces and can be used to close smaller cracks on a painted wooden terrace. Make sure the old paint adheres well and the area is clean and dry.

Yes, the product can be used to seal leaky balcony floors on tiles. The fiber-reinforced sealant is flexible and waterproof and also bridges slight movements in the substrate.

Yes, WF-157404 is very suitable for sealing leaky concrete foundations in the garden. It also reliably seals cracks on slightly damp surfaces and is immediately waterproof.

Yes, the mass can be easily applied with a brush. It reliably bridges cracks and small holes.

Yes, Aqua Dicht adheres excellently to concrete and reliably bridges cracks thanks to the fiber reinforcement.

Unfortunately, the product data we have does not contain specific information on the suitability of Aqua Dicht for PE plastic. A data sheet is also not included in the information provided. We recommend that you consult the product page on Westfalia.de or contact our technical support for these details.

No, Aqua Dicht is not suitable for walkable surfaces. For terraces, it is only ideal in places that are not walked on or on vertical surfaces.

With a 1-liter can of Aqua Dicht, you can cover approximately 1 to 1.5 square meters, depending on the layer thickness and the condition of the substrate. For highly absorbent or very uneven surfaces, consumption may be higher. (Roughly: for 5 m² of wall surface you need about 3-5 cans).

The fiber reinforcement of Aqua Dicht provides high flexibility and crack bridging. It is therefore well suited to permanently seal smaller, slightly movable joints up to approx. 2 mm wide.

Aqua Dicht adheres excellently to many common building materials such as concrete, stone and metal. On heavily sanded roofing felt or bitumen shingles, adhesion may be impaired; here the surface should be cleaned beforehand and, if necessary, primed.

Yes, Aqua Dicht is weather and UV resistant and offers long-term protection against the elements, even in direct sunlight.

The fiber-reinforced formula bridges holes and cracks and adapts flexibly to uneven surfaces. It is extremely robust and at the same time so elastic that it withstands movements without tearing.