2-speed cordless drill WAS18 18 Volt (Without battery and charger)

Yes, the 1st gear with an idle speed of 0-400 rpm is specially designed for fine work. In combination with the 19+1 torque settings, this enables very careful screwing in of small screws.

Yes, the 19+1 torque settings up to 30 Nm are specifically designed to precisely adapt the power of the WAS18 to the material. This allows screws to be screwed in in a controlled manner and prevents over-tightening or damage to the material.

Yes, the WAS18 weighs only 860 g without a battery and is designed for longer use. The low weight significantly reduces fatigue when working overhead and feels good in the hand.

The integrated LED light of the WAS18 is designed to illuminate the work area. It helps in poor lighting conditions to better see screws and holes.

The WAS18 is part of our 18-volt battery system and is compatible with all 18-volt batteries from this series. Batteries and chargers are available separately.

Yes, the 2-speed gearbox of the WAS18 allows for a finer adjustment of the speed. This is ideal for sensitive materials and precise screwing to avoid damage.

Yes, the scope of delivery includes the WAS18 cordless drill itself, the belt holder and the integrated LED light. Battery and charger must be purchased separately.

Yes, the WAS18 is ideally suited for furniture assembly with its 2-speed gearbox and 30 Nm torque. The integrated LED light also helps in poor lighting conditions.

The WAS18 is ideally suited for furniture assembly with its 2-speed gearbox and 30 Nm torque. The power and the two gears enable fast work.

The belt holder is very practical for safely and easily storing the drill when working on ladders or in hard-to-reach places. It ensures free hands.

The 10mm quick-release chuck of the WAS18 is designed for common drill sizes up to 10 mm and also holds smaller diameters from approx. 1.5 mm securely. It is ideally suited for 2mm drills.

Yes, the WAS18 with its 2-speed gearbox and 30 Nm torque is also well-suited for smaller drillings in wood. The gearbox allows for an adjusted speed.

For softer old walls like brick or plaster, the drill is usually suitable. For harder materials like solid concrete or natural stone, an impact drill with impact function is required.

Yes, the compact design and the integrated LED light make the WAS18 well-suited for working in tight or poorly lit areas.

Yes, the 19+1 torque settings allow a very precise adjustment of the force. This way, you can also screw screws into thin or sensitive materials without damaging them.

The 2-speed gearbox allows the speed of the WAS18 to be well regulated. This allows you to screw in screws in a controlled manner and minimize splitting the wood when assembling furniture.

The 10 mm quick-release chuck enables lightning-fast tool changes. The speed can be adjusted continuously and the 2 gears can be easily switched to quickly switch between different materials.

For general DIY tasks and furniture assembly, a 2.0 Ah battery is usually sufficient. (roughly calculated: a 2.0 Ah battery allows about 30-45 minutes of continuous operation when screwing). For more intensive use, batteries with a higher capacity are recommended.

With 30 Nm of torque, the drill offers sufficient power for most screwing work in wood and common materials. For very hard woods or large screws, pre-drilling may be recommended.

The WAS18 is equipped with a 10 mm quick-release chuck. This enables lightning-fast tool changes without an additional key.

The LED light of the WAS18 is designed exactly for this, to illuminate the work area. It improves visibility, especially in dark or hard-to-reach areas.

The low weight of only 860 g and the ergonomic 2-component handle of the WAS18 are explicitly designed for longer use. The device feels good in the hand even after hours and prevents fatigue.

Yes, the 10 mm quick-release chuck is designed for standard hex bits and drill bits up to a diameter of 10 mm. This allows you to use a wide range of accessories.

Yes, the drill has a drilling capacity of 10 mm in metal. That's enough for holes in thin aluminum profiles or similar materials.

The WAS18 is suitable for use in the garden, but should be protected from direct moisture and heavy dust. Cleaning the device after use is recommended.

The WAS18 is designed for drilling in metal (up to 10 mm) and wood (up to 20 mm). A hammer function for masonry or stone is not available on this model, so it is not suitable for this.

With 30 Nm of torque, the WAS18 offers enough power for typical screwing work. Longer screws in spruce wood should be easy to work with.

Yes, the WAS18 is easy to handle for beginners with its moderate weight and simple controls. The LED light also improves visibility of the work area.

Yes, the ergonomically shaped 2-component handle ensures a secure grip and comfort, even during prolonged use. The low weight of 860 g also contributes to fatigue-free work.

The WAS18 with its 2-speed gearbox and torque of 30 Nm is ideal for furniture assembly and therefore also suitable for chipboard. This enables an efficient working speed.