Titanium-coated saw chain for 50 cm guide bar, 72 drive links, 1.5 mm gauge, .325" pitch

No, this chain is designed for a drive link thickness of 1.5 mm. A 1.6 mm kerf width would be too large, which can lead to imprecise guidance and increased wear.

The chain is correctly tensioned when it can still be pulled by hand on the guide bar, but does not sag. It should be able to be lifted about 3-5 mm.

The saw chain is designed for general sawing work. When working with hardwood, an always sharp chain and sufficient chainsaw power are crucial for optimal and efficient cutting results.

Yes, if your gasoline saw uses a 50 cm bar and the pitch of 0.325", the drive link thickness of 1.5 mm and 72 drive links match, the chain is compatible.

Yes, with the appropriate chainsaw power and correct assembly, the chain is designed for efficient sawing of branches and wood. The 50 cm length allows for the processing of larger diameters.

No, the number of drive links must match the guide bar exactly. A chain with 72 drive links is designed for a 50 cm long bar with a 0.325" pitch, which requires exactly this number of links.

Yes, this chain is suitable for electric and gasoline chainsaws, as long as the guide bar is 50 cm long and the other specifications (72 drive links, 1.5 mm groove width, 0.325" pitch) match.

No, this chain is specially designed for a 50 cm guide bar. The chain would be too long for shorter bars.

The pitch is the distance between three consecutive rivets, divided by two. It can be checked with a caliper or a template.

The "Titan" chain is designed for its high robustness and durability. However, regular maintenance and sharpening are essential for daily professional forestry use.

Yes, this saw chain is specially designed for 50 cm bar lengths. It has a drive link thickness of 1.5 mm and a pitch of 0.325".

Yes, this saw chain has a pitch of 0.325 inches (0.325"). If the drive link thickness of 1.5 mm and the number of 72 drive links also fit your saw, it is compatible.

A sharp saw chain like the "Titan" supports precise and straight cuts. However, the quality of the cut also depends on the chainsaw, the guide bar, and the cutting technique.

Yes, the Titan chain is suitable for corresponding felling work, provided your chainsaw with a 50 cm bar has the necessary power for the tree diameter. Always pay attention to safe cutting.

You can best measure the groove width with a caliper on the guide bar. It should be exactly 1.5 mm so that the chain is guided correctly.

Yes, the "Titan" saw chain has exactly these specifications: 72 drive links, 1.5 mm drive link thickness and a pitch of 0.325". It is suitable for a sword length of 50 cm.

The "Titan" saw chain actually stays sharp longer thanks to its electrolytically chrome-plated cutting teeth, even under high stress such as sawing hardwood. This reduces the need for frequent resharpening.

The cutting teeth of the chain must point forward in the direction of rotation of the chainsaw. The cutting edges should be aligned towards the tip of the guide bar.

As long as the guide bar of your battery-powered chainsaw meets the specifications (50 cm length, 1.5 mm groove width, 0.325" pitch, 72 drive links), this chain is compatible. The type of drive (battery/petrol) is not crucial for the chain itself.

The Titan chain can also be used for wet wood. In general, sawing wet or resinous wood can dull the chain faster than with dry material.

Yes, the chain is also suitable for older gasoline chainsaws, as long as the guide bar is 50 cm long, the groove width is 1.5 mm and the pitch is 0.325".

Yes, with this saw chain you benefit from faster sawing compared to standard chains. The optimized geometry and high-quality workmanship enable more efficient work and thus time savings.

Yes, it is recommended to thoroughly clean the chain before storage and then lightly moisten it with commercially available chainsaw oil. This protects against corrosion.

The electrolytically chrome-plated saw teeth are particularly robust and designed for high stress. The chain is made of steel and is resistant, which also makes it well suited for more demanding sawing work.

The saw chain has exactly 72 drive links. Please check if this number fits your guide bar.

For this saw chain, you can use any commercially available chainsaw oil. Make sure there is sufficient lubrication to maximize the life of the chain.

The chain with its 50 cm cutting length and specifications supports clean and efficient work on larger branches. The cutting speed depends primarily on the power of your chainsaw.

Yes, the chain can also be used for thin branches, as long as the chainsaw is suitable for this. Correct chain tension is, as with all sawing work, crucial for safety and cutting results.

Yes, the chain is also suitable for electric saws with a 50 cm bar if the other specifications such as pitch (0.325"), 72 drive links and drive link thickness (1.5 mm) match.

Yes, it is common and important to retighten a new chain after a short operating time. New chains stretch a bit at first. Check the chain tension regularly.